Check items to add to the cart or select all
- This case was designed for a 500/4 lens with a body attached, but will also hold other combinations. It is called a “compact” long lens case because the diameter is smaller than the L521 PolyCore™ 500 case — it is too small for 400/2.8 and 600/4 lenses. It is also lighter in weight and offers less protection.
- We have had a number of complaints because 200-400s, 400/4s and 300/2.8s get lost in this case. We strongly advise purchasing the L029 Foam Insert (which reduces the diameter near the front element) or consider purchasing the E660 or E970 lens pouch instead.
- Increase the height of your case — the L128 deep lid will fit these cases with a special L228 made-to-order adapter strap (the L128 was designed for the PolyCore series cases which utilize a removable lid, so this adaptation is a little goofy).
Product Update: We are transitioning from a solid nylon fabric pocket (as shown in most product photos) to a mesh pocket as shown in above detail photo.
Also, all L511s now (since 2012) have a sewn-in side handle, so the case can be carried either vertically or horizontally!
- Nikon or Canon 500/4 or Nikon 200-400/4 lens with a full-sized body attached (with quick-release plate attached) with hood reversed (with leatherette lens cover).
- 300/2.8 with full-sized body attached with hood in shooting position (with leatherette lens cover) + teleconverter.
- Nikon 600/4 AF-S: The following combination will fit inside this case: Nikon 600/4 AF-S with the larger diameter hood piece removed and with a Moose Peterson lens cap & Kirk low-profile tripod foot (Sept. 2005).
- Nikon 200-400/4: The following combination will fit inside this case (w/ about an inch to spare): 200-400 with the 1.4x teleconverter and hood reversed with a body (D90) attached (Oct. 2009).
- Nikon 600/4 VR II: “The hood diameter of this lens is 7-½" without soft cover and 8-½" with soft cover, both being too large to fit into this case.” No report on whether or not this lens without a hood will fit (March 2011).
- One A257 or M330 can be attached in the lower center of the case (standard position & shown in photos).
- Two single-wide pouches (E105, E280 etc.) can be attached to either side of the lower A257, covering the collapsible pockets. Alternately, a double-wide pouch (A257, M330 etc.) can also be attached to either the left or right of the standard A257 Body Pouch, but this attachment location is a little loose which may cause the pouch to shift around a little, unless secured with a Y205 strap.
- The upper part of the case will house an equal amount of pouches, except it has additional attachment points, so two single-wide pouches can be attached in the center. Back (flat) Side of the Case
- A double-wide pouch (A257, M330 etc.) can be attached to the lower back or flat part of the case, although this disables use of any backpack harness or may make using a shoulder strap awkward.
Tripod Use Remove the A257 center pouch (shown in photo above) and replace it with a T164 or T317 pouch for attaching a tripod (see this page for pix). Attach a Y204 to the top of the case to hold the top part of the tripod. The A257 can then be reattached to the upper or lower part of the case, slightly off center.
In November of 2011 we made this case 15mm taller.
Double-wide allotment on belt or pack frame. (Realistically, this case is too large to conveniently wear on a belt).
20-3/4h x 7" dia I.D.
21-3/4h x 9" dia O.D.
Volume = 1005 cu in
Weight with A257 pouch & shoulder strap: 2 lbs. 4 oz.
53h x 17.8cm dia I.D.
55h x 23cm dia O.D.
Volume = 16.5 lit Weight with A257 pouch & shoulder strap: 1010 g
I.D. = Inside Dimension | O.D. = Outside Dimension
The “dia” is the maximum diameter of the front element and/or lens cover that will fit inside this case. The circumference is 66cm (26") and measures the entire inside perimeter of the "D" shape of the case. It is larger than 3.14 times the diameter to allow extra room for the lens tripod foot.